FEATURES

The Polycarbonate Rolling Security Grilles come with many unique features. Firstly, the finish is clear and anodized. Secondly, they come with an electric motor operator. Thirdly, they are highly resistant and surprisingly light. Additionally, they have polycarbonate panels.

SPECIFICATION

Curtain

The manufacturers make the curtain of 3” (76mm) on center extruded aluminum sections. Moreover, each section framed by a continuous double “C” hinge holds clear polycarbonate panels 1/16” (1.6mm) thick x 2 1⁄2” (64mm) high x 15” 3⁄4 (400mm) wide separated by 2 1⁄2” (64mm) high x 0,050” (1,3mm) thick aluminum slats.

Support Structure

Please choose between:

• 3” (76mm) X 3” (76mm) structural tubes with 0.120 (3mm) wall thickness furnished by MobilFlex to be pre-drilled and tapped for guides and endplates. Also, lines will attach to the floor slab and joists above. Furthermore, the attachment at the top is for lateral support only.
• 2” (50mm) X 3” (76mm) steel angles for the face of the wall installation. (instead of steel tubes).
• 4” (101mm) X 4” (101mm) structural tubes (for openings over 250 sqft (2.3m2)).

End Plates

Furnish steel plates not less than 3/16” (4.7mm) thick (with dimensions appropriate to coil size) to support the ends of the barrel assembly with sealed, self-aligning shaft bearings. Furthermore, we will bolt the endplates to keep the tubes.

Barrel

Minimum 6 5/8″ (168mm) diameter X 0.156 (4mm) wall steel pipe barrel is made to carry curtain load with a maximum allowable deflection of 0.03″ per foot of closure width (2.3mm per linear meter in width)—barrel to house a torsion spring counterbalance assembly to counter-balance the curtain.

Counter Balance

Oil-tempered, helical torsion spring(s) pre-lubricated and secured around a continuous, solid, cold-rolled steel inner shaft will act as a counterbalance within the barrel. Additionally, the post will bear on self-aligning, permanently lubricated ball-bearing assemblies. Furthermore, the counterbalance assembly is made for a minimum life of 20,000 cycles. Also, the spring to be site-tensioned by an attached, accessible charging wheel.

Manually Operated

Standard closure to have manual push-up, pull down with removable retrieval rod. The effort to raise or lower the closure shall not exceed 15 pounds (7kg) force. (Optional but not recommended, hand chain hoist or hand crank with removable crank handle). Motorized operation is better for closures with an area greater than 150 sqft (14m2).

Electric Motor Operator

The motor operator shall be industrial duty, jackshaft hoist type. In addition, the primary reduction shall be a heavy-duty belt drive with chain-and-sprocket secondary reduction. The mechanism is self-locking when applying torque to the output shaft. Furthermore, the operator shall have an adjustable, torque-limiting friction clutch. The motor operator shall have a built-in interlock that will prevent damaging the grille if you operate it electrically when in the locked position.

Emergency Egress Release:

Supply a flush manually activated emergency egress device to disengage the motor in an emergency.

Electric Key Switch:

Control station (when applicable) shall be in two positions, open/close, constant pressure type for flush mounting, housed in a tamper-proof enclosure (key switch to replace push button set).

Guides

Vertical curtain guides are to be of extruded aluminum 1 5/8″ (41mm) wide x 2 3 4″ (70mm) deep with a nylon brush seal to allow smooth operation. Top stoppers are to be on each guide to stop the upward movement of the curtain at a secured position.

Bottom Bar

Heavy-duty extruded aluminum section, bell-shaped to provide reinforcement. Bottom bar to house lock mechanism. Center lock mechanism to be a 2-point deadlock that activates 7/16″ (11mm) steel lock bars at each end. Standard MobilFlex cylinders are operable from both sides. Removal of the bottom bar is not necessary to change the cylinders. For counter closures, the bottom bar is to be of extruded aluminum 1 1 4″ (32mm) wide x 3″ (76mm) high.

Cylinders

The locking bottom bar will have a MobilFlex 1” (2.5mm) 5-pin mortise cylinder.
Please choose:1 a cylinder (inside or outside) or
Two cylinders.

Material & finish

Standard aluminum 6063-T5 shall be a clear anodized finish or acrylic paint white or black.

Option (Please specify if you require a hood)

POLYCARBONATE ROLLING SECURITY GRILLES  INSTALLATION

Canuck Door Systems is a dealer of Mobiflex, the leading manufacturer of security grills in Canada.

We install rolling security grilles in the Toronto, Mississauga, Brampton, Vaughan, Richmond Hill, Markham, Hamilton, Burlington, Oakville, Pickering, Ajax, Oshawa, Aurora, Newmarket, and throughout South Ontario is no exception.

Canuck Door Systems also installs Perforated Steel Rolling Security Grilles, Open Style Rolling Security Grilles, and Open Style Roll-Up Security Gates.